How To Build a Solar Panel

The first step of learning how to build a solar panel is to look for a copper sheet. It can be more easily acquired than silicon; besides, like silicon, copper has photoelectric capabilities. Approximately one-half square foot of copper sheet is necessary, but since the hardware sells large sheets, then you can still store the remaining part of the sheet or make more cells.

It aren't difficult to build your own DIY solar panels. You will need a decent stove to create the cells. An electric one with hot plates instead of coils would be perfect but not a must. The copper sheet should be cut to fit the burner. The sheet and your hands should be washed in soap and water to eliminate dirt or other materials. The copper sheet should be brushed with a copper wire or sandpaper. This will ensure that light corrosion is eliminated. After the sheet has dried, this should be placed on top of the stove burner and the heat turned on to the highest capacity that the stove can make.

Watch the copper sheet heat up, but make sure you don't touch it. Orange or red colors will appear as the sheets are heated. Continue heating even when blank flakes can be seen forming on top of the sheet. Then a black layer of cupric oxide is observed and should be allowed to be heated for more than thirty minutes to ensure that the black coating will become thicker and will easily flake off from the original copper sheet. You will know if the sheet is not cooked well because the black coating will just stick to the original sheet. The heat should be turned low then off.

After the heating process, you should allow the burner and the sheet to cool off by themselves. Do not come too near the sheet because some bits of hot copper might come off the sheet and give off sparks of tiny metal dust. After the sheet has cooled, you should lightly brush some of the small bits of copper that are stuck in the sheet. The red layer will be the one used for the solar panels.

You should cut a similar size of copper sheet and bend them together lightly. Arrange them in a plastic bottle but do not allow them to touch each other. Attach one alligator clip lead to the heated copper sheet and one to the unheated sheet. The lead from the heated plate should then be attached to the positive point of a micro-ammeter with 10 to 50 mA capacity; the other lead should be at the negative point.

Make a salt solution and add to the jar without wetting the leads. One inch of the copper sheets should not be soaked in the solution. You can now bring this to where the sun can be seen, and the solar panel ammeter will show activity.

Get started with installing your own home solar power systems today! Enjoy saving over 80% of your electrical costs and contribute in saving our planet. Solar energy - The environmental friendly way to generate free energy for your and your family.

If you are interested to learn more about how to build a solar panel, visit:
http://www.greenearth4energy.com

You may also want to get your solar installation guide here:
http://www.earthenergyguide.com

Useful information home solar power systems:
http://www.greenearth4energy.com/solar-panel-systems.html

Learn how to build a solar panel:
http://www.greenearth4energy.com/build_solar_panel.html

Learn how to DIY  solar panels:
http://www.prlog.org/10295698-diy-solar-panel-complete-analysis-on-home-solar-power-systems.html

How To Build a Perpetual Motion Machine

Many new ideas have been tested and researched to harness energy from different sources. For instance, wind turbines have been used to harness energy from the wind. Solar power systems are used to generate electricity from the sun. And now, we have across a new source of energy that perhaps only a few people have taken notice: magnetic energy. This source of energy source is used through a magnetic energy generator.

The magnetic power generator runs through the force field created by the magnets' opposing force. This machine is known as the perpetual motion machine. A huge amount of skepticism has been already been accumulated among the people for the past 10 years, the machine has survived and is now generally accepted as a new source of energy. It is not true that the magnet motor energy will run for eternity and will never stop, as the word perpetual implies. This was only said so because the machine can last up to hundreds of years. Some claimed that it has the ability to last up to 400 years.

Currently, this machine is not yet available in a large scale. The machines are just sold to homeowners and small businesses. However, a simple machine can actually work up to 7,000 watts. This is enough to power up the electrical supply of an entire household including appliances that are heavy on electricity wattage. All you need to do now to use the magnet motor energy is to buy your magnet motor energy manual and start building your own machine. This is very cost effective and is very easy to build.

This is how a perpetual motion machine works:

When you connect the north and the south polarity of a magnet the opposite way, they will repulse each other. A third magnet in the middle will create a force field between these magnets. This force field can then be converted to energy and can help you generate electricity.

These are some of the benefits of a perpetual motion machine:

• It can cut your electrical bills in half or even completely eliminate it.
• It is an environmentally friendly machine and does not cause any pollution.
• It works in all weather conditions.
• It doesn't require a large amount of space.
• Low maintenance costs.
• You can build and install it for less than $100.
• It's completely safe even with children near the vicinity. It isn't flammable or combustible.
• You don't have to be a scientist to construct this machine. The process is very easy, especially if you get your hands on some good building plans. The materials are affordable and can be found at your local hardware store.

If you are interested to learn how to build a perpetual motion machine, visit
http://www.greenearth4energy.com/build_magnetic_generator.html

To get your installation guide, proceed to:
http://www.greenearth4energy.com/magniwork

Useful information magnetic energy generator:
http://www.greenearth4energy.com/benefits_magnetic_generator.html

Useful information magnetic power generator:
http://www.greenearth4energy.com/magnetic_power_generator.html